Specificaties
Temperature Warning Alert
Easy InstallationComing with easy, user-friendly setup, the Pacific Temperature Sensor allows users to obtain the ultimate performance from their liquid cooled PC by simply connecting the power cable to it.
*Note:
1. Please check your system immediately to prevent any hardware damages when the alert is triggered. The default alarm temperature is 45℃.
2. Please check the melting point or maximum operating temperature of each cooling component before you manually adjust the temperature threshold.
Thermaltake recommends the following steps to be taken after completing your water loop setup
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
- DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
- Fill the reservoir to the top as it will prevent air from going into the pump
- If necessary tilt the system slightly from side to side to bleed the air out of the loop.
- Place some paper towels under fittings and joining points to test for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop
- Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
- Coolant might fade over time.
specificaties
| P/N | CL-W151-CU00BL-A |
| Dimension | 35.5 H x 32.7 W x 54 L (mm) |
| Weight | 64 g |
| Material | Copper + ABS |
| Rated Voltage | 5V |
| Power Input | 0.3W |
| Screw Thread | G 1/4 |
| Connector | 4 pin Molex |
* Specifications are subject to change without notice.
* The product picture(s) is only for your reference, it may differ from the actual product.
Specificaties
Temperature Warning AlertEasy InstallationComing with easy, user-friendly setup, the Pacific Temperature Sensor allows users to obtain the ultimate performance from their liquid cooled PC by simply connecting the power cable to it.
*Note:
1. Please check your system immediately to prevent any hardware damages when the alert is triggered. The default alarm temperature is 45℃.
2. Please check the melting point or maximum operating temperature of each cooling component before you manually adjust the temperature threshold.
Thermaltake recommends the following steps to be taken after completing your water loop setup
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
- DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
- Fill the reservoir to the top as it will prevent air from going into the pump
- If necessary tilt the system slightly from side to side to bleed the air out of the loop.
- Place some paper towels under fittings and joining points to test for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop
- Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
- Coolant might fade over time.
specificaties
| P/N | CL-W151-CU00BL-A |
| Dimension | 35.5 H x 32.7 W x 54 L (mm) |
| Weight | 64 g |
| Material | Copper + ABS |
| Rated Voltage | 5V |
| Power Input | 0.3W |
| Screw Thread | G 1/4 |
| Connector | 4 pin Molex |
* Specifications are subject to change without notice.
* The product picture(s) is only for your reference, it may differ from the actual product.
