Specificaties
Thermaltake Pacific Flow Indicator TwoDesigned for C1000 Opaque Coolant, the new Pacific Flow Indicator Two features a spiral shaped blade design that spins when liquid flows through the system, giving immediate visualization of flow. With easy installation, exceptional performance and unrivalled reliability, the Pacific Flow Indicator Two is manufactured with high quality ABS and PETG, compatible with all standard G1/4 fittings, plus, it comes in three colors in a pack (black, red and white) to make the system more aesthetically pleasing while ensuring a great cooling solution.
Tt LCS CertifiedTt LCS Certified is a Thermaltake exclusive certification applied to only products that pass the design and hardcore enthusiasts standards that a true LCS chassis should be held to. The Tt LCS certification was created so that we at Thermaltake can designate to all power users which chassis have been tested to be best compatible with extreme liquid cooling configurations to ensure you get the best performance from the best features and fitment.
High-Flow DesignBoth ends of the Pacific Flow Indicator Two are compatible with all G1/4 fittings so users can use any standard fitting on each end. Besides, thanks to the plug and play design, no additional tools needed for the installation, and it is ready to work in seconds.
Easy & Flexible Application
Pacific Flow Indicator Two allows enthusiasts to build a superior water cooling system from an aesthetic standpoint and incorporate externally-modular upgrades into their chassis.
Caution
Thermaltake recommends the following steps to be taken after completing your water loop setup
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
- DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
- Fill the reservoir to the top as it will prevent air from going into the pump
- If necessary tilt the system slightly from side to side to bleed the air out of the loop.
- Place some paper towels under fittings and joining points to test for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop
- Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
- Coolant might fade over time.
Specificaties
Thermaltake Pacific Flow Indicator TwoDesigned for C1000 Opaque Coolant, the new Pacific Flow Indicator Two features a spiral shaped blade design that spins when liquid flows through the system, giving immediate visualization of flow. With easy installation, exceptional performance and unrivalled reliability, the Pacific Flow Indicator Two is manufactured with high quality ABS and PETG, compatible with all standard G1/4 fittings, plus, it comes in three colors in a pack (black, red and white) to make the system more aesthetically pleasing while ensuring a great cooling solution.
Tt LCS CertifiedTt LCS Certified is a Thermaltake exclusive certification applied to only products that pass the design and hardcore enthusiasts standards that a true LCS chassis should be held to. The Tt LCS certification was created so that we at Thermaltake can designate to all power users which chassis have been tested to be best compatible with extreme liquid cooling configurations to ensure you get the best performance from the best features and fitment.
High-Flow DesignBoth ends of the Pacific Flow Indicator Two are compatible with all G1/4 fittings so users can use any standard fitting on each end. Besides, thanks to the plug and play design, no additional tools needed for the installation, and it is ready to work in seconds.
Easy & Flexible Application
Pacific Flow Indicator Two allows enthusiasts to build a superior water cooling system from an aesthetic standpoint and incorporate externally-modular upgrades into their chassis.
Caution
Thermaltake recommends the following steps to be taken after completing your water loop setup
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
- DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
- Fill the reservoir to the top as it will prevent air from going into the pump
- If necessary tilt the system slightly from side to side to bleed the air out of the loop.
- Place some paper towels under fittings and joining points to test for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop
- Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
- Coolant might fade over time.
